CAT 3126B Engine Specs for Yachts / Boats / Trucks

The Cat 3126B engine is designed and built to take full advantage of a “gear fast, run slow” strategy. Unlike mechanically governed engines of the past, the fully electronic 3126B need not be gear-bound to limit maximum vehicle speed — this should be done using Vehicle Speed Limiting (VSL) and Protection.

For the best balance of performance and fuel economy, spec axle ratios and tire sizes to obtain: 2000 rpm @ 60 mph (97 km/h) subject to the following: Maximum cruise speed of 65 mph (105 km/h) or below. Maximum recommended engine speed at cruise — 2400 rpm. Minimum recommended engine speed at a cruise speed of 55 mph (89 km/hr) — 1800 rpm.

CAT 3126B Engine Specs

420-860 lb-ft @ 1440 rpm Peak Torque, 6-Cylinder, 4-Stroke-Cycle Diesel
Bore — in (mm) - 4.33 (110)
Stroke — in (mm) - 5.0 (127)
Displacement — cu in (L) - 439 (7.2)
Aspiration - ATAAC1

CAT 3126B Engine Compression Ratio

175-300 hp - 16:1
Rotation (from flywheel end) - Counterclockwise
Cooling System2 — gal (L) - 3.5 (13.2)
Lube Oil System (refill) — gal (L) - 4.75 (18.0)3
Weight, Net Dry (approx) — lb (kg)
Including Flywheel - 1295 (588)
1 Air-to-Air AfterCooling
2 Engine Only. Capacity will vary with radiator size and use of cab heater.
3 Optional 28L (7.5 gal) oil pan also available in some chassis.

CAT 3126B Engine Accessory Equipment

Air compressor: gear driven, 0.37 m3/min (13.2 cfm) or 0.46 m3/min(16.5 cfm)
Air conditioner compressor mounting
Air inlet elbow
Auxiliary brake compatible (exhaust)
Ether starting aid/adaptation
Fan drive mounting bracket
Fan drive
Front engine support
Front PTO adapter
Jacket water heater
Rear power take-off
Starting motor: 12 V or 24 V
Turbocharger compressor outlet elbow
Hydraulic pump drive, SAE A

CAT 3126B Engine Standart Equipment

Air inlet manifold heater
Cooling: belt-driven jacket water pump, oil cooler
Crankcase breather
Electronic Control Module (ECM)
Electronic Data Link, SAE J1922, J1939, ATA J1587
HEUI Fuel System (Hydraulically actuated, Electronically controlled Unit Injector)
Flywheel and SAE No. 1 or SAE No. 2 housing
Fuel: spin-on secondary filter, transfer pump, hand priming pump
Governor: full-range, electronically controlled
Lifting eyes
Lubrication: gear-driven pump, front or rear sump, full flow spin-on filter, left-hand side oil level gauge (dipstick)
Turbocharger
Vibration damper

CAT 3126B Engine Dimensions

Caterpillar 3126B Engine (DM3276) Performance Data

Max hp (kW) - 175 (131)
Advertised hp (kW) - 175 (131)
Operating Range (rpm) - 1440-2500 (1060)
Maximum Engine rpm - 2640
Governed Speed rpm - 2500
Peak Torque — lb-ft (N•m) - 420 (569)
Peak Torque rpm - 1440
Torque Rise (%) (Gov. rpm) - 25
Altitude Capability — ft (m) - 10 000 (3050)

Caterpillar 3126B Engine (DM4201) Performance Data

Max hp (kW) - 207 (154)
Advertised hp (kW) - 190 (142)
Operating Range (rpm) - 1440-2500 (1060)
Maximum Engine rpm - 2640
Governed Speed rpm - 2500
Peak Torque — lb-ft (N•m) - 520 (705)
Peak Torque rpm - 1440
Torque Rise (%) (Gov. rpm) - 27
Altitude Capability — ft (m) - 10 000 (3050)

Caterpillar 3126B Engine (DM3287) Performance Data

Max hp (kW) - 330 (246)
Advertised hp (kW) - 330 (246)
Operating Range (rpm) - 1440-2400 (960)
Maximum Engine rpm - 2640
Governed Speed rpm - 2400
Peak Torque — lb-ft (N•m) - 860 (1166)
Peak Torque rpm - 1440
Torque Rise (%) (Gov. rpm) - 19
Altitude Capability — ft (m) - 10 000 (3050)

CAT 3126B Engine Electronic Features

Electronic self-diagnostics
Compatible with Caterpillar electronic technician (ET), electronic control analyzer programmer (ECAP), and MPSI Pro-Link service tools
Cold weather startup strategy and electronic idle control functions
ECM storage of operational, maintenance, and diagnostic data
J1939 compatible — ABS, Allison WT
Customer selectable, re-programmable operational parameters:
• Engine Monitoring System — off, warning, derate, or shutdown
• Cruise control with exclusive SoftCruise
• Vehicle speed [mph (km/h)] limiting and protection
• Idle shutdown timer & override
• 2-speed fast idle
• Maintenance monitor [miles (km) or hours]
• Cooling fan control
• Customer password protection
• Exhaust brake operational modes
• Theft deterrent
• Adjustable low idle rpm
• OEM parameter lockout
Programmable Power Take-Off (PTO) functions:
• Adjustable speed control [mph (km/h)] of vehicle while in PTO mode
• Adjustable maximum engine rpm speed
• Adjustable minimum engine rpm speed
• Limit engine torque to driven equipment
• Adjustable ramp rate up or down between PTO set speed(s)
• Adjustable rpm “bump” intervals
• Selectable PTO configuration for “in cab” or station of remote operation

CAT 3126B Gearing Considerations

Depending on the application, the absolute minimum startability in first gear should be 6 percent, preferably in excess of 10 %.

On/off highway severe service applications will require considerably greater startability. Minimum gradeability should be 1.5 percent (1.8 percent recommended) at peak torque in top gear, and 0.5 percent at cruise rpm.

To further optimize the matching of your truck to the performance characteristics of the engine, a computerized spec’ing tool called Caterpillar Truck Engine Pro (TEP) is offered by your Caterpillar dealer. It calculates the effects of various driveline variables on engine operation such as transmissions, axles, and tires. This lets you see the results before you finalize your truck specs.

Comments

Tommy Stone said…

I didn't know that the CAT 3126 engine was installed on yachts! What types of vessels is this motor available for? Big or small boats?

2:19 PM

CAT C-16 / C-15 Diesel Engine Specs for Heavy-Duty Trucks

Caterpillar C-16 Truck Engines offer a wide operating range and high torque rise which promotes the use of transmissions with fewer gears. Even with this built-in feature, heavy/specialty haulers must remember their trucks should be geared to achieve the appropriate compromise between startability and desired road speed. Typical loads of 80 000 Ib or less are less affected by improper drive train specing than are heavy haulers. In general, either application shares one similar recommendation - gear fast/run slow is essential for good fuel consumption. If any of the following conditions are present, special attention should be given to proper transmission and axle specifications. A complete Caterpillar Truck Engine Pro (TEP) C-16 analysis is available from your local Caterpillar or truck dealer. CAT C-16 / C-15 Diesel Engine for Heavy-Duty Trucks Crankcase breather, valve cover mounted Electronic data link, ATA/SAE Electronic control module (ECM) Electronically controlled

Caterpillar 3208 TA Engine Specs & Key Features

The Caterpillar 3208 TA Marine Engine is designed to meet the rigorous demands of the marine environment. Whether you're operating a commercial fishing vessel, a yacht, or a workboat, this engine offers unmatched performance and versatility. With its turbocharged and aftercooled design, the 3208 TA delivers impressive power, ensuring you can navigate through rough waters and reach your destination quickly and efficiently. But it doesn't stop there – the Caterpillar 3208 TA Marine Engine is also highly fuel-efficient, ensuring you can make the most of every drop of fuel. Its advanced engine management system optimizes fuel delivery and combustion, resulting in reduced emissions and lower operating costs. With enhanced fuel economy, you can extend your range and spend more time on the water enjoying the journey. Caterpillar 3208 TA Engine Specs V-8, Four-Stroke-Cycle Diesel; Emissions - IMO compliant; Bore — mm (in) - 114.3 (4.5); Stroke — mm (in) - 127 (5.0); Displacement

Caterpillar D2 Diesel Tractor, 1938

The Caterpillar D2 diesel engine required a gas fueled pony motor to crank the diesel up to speed. The pony motor originally was recoil starting, but later models were electric start. The operator would start the pony motor and when the diesel engine was up to running speed and hot enough, about 15 minutes, the operator would turn on the diesel fuel valve and, hopefully, the fuel would fire and Cat D2 engine would run start running. The operator would shut off the gas flow to the pony motor and release the clutch to disengage it from the diesel engine. It was a little more complicated than this, what with releasing the decomp and other manipulations... Cat D2 weighed between 6000 and 6700 lbs. Caterpillar D2 was manufactured from 1938 through 1956. Caterpillar D2 Diesel Tractor Specs Length - 108 in (274 cm); Height - 57.5 in (146 cm); Weight - 7,420–8,536 lb (3,366–3,872 kg); Propulsion - Caterpillar tracks (12 in (30 cm)); Engine model Inline-4 cyl diesel eng

How Catalytic Converters Work

If you’re interested in vehicles as well as keeping our Earth safe, you may be interested in learning more about catalytic converters and how these important devices help to combat against pollution. These devices are a great way to help keep the air around us clean. While this is a hot topic, many people have questions about the use of catalytic converters. Take a look at the following information to learn more about catalytic converters. What is a catalytic converter? A catalytic converter is a device that helps to turn toxic byproducts found in an engine into less toxic substances through the use of chemical reactions. As a car runs, the catalytic converter turns pollutants into less harmful substances before they leave a vehicle through the exhaust pipe . This can help to clean up the air significantly! Are catalytic converters only found in standard automobiles? No! While they are found in standard automobiles, they are also in many other machines. This includes buse

Caterpillar 247B & Cat 257B Multi Terrain Loaders

The B-Series machines employ the proven anti-stall system and pilot hydraulic joystick controls that make Caterpillar Multi Terrain Loaders easy to operate. B-Series improvements include a deluxe joystick design that incorporates positive-action buttons to control work tool hydraulic or electrical functions. An ergonomically designed arm bar is rounded and sculpted to provide superior operator comfort, and the redesigned gauge panels are easy to read. The B-Series cab offers a new door option with 25 percent more glass that improves sight lines to the working area. CAT 247B / 257B Multi Terrain Loader Specs Caterpillar 247B Caterpillar 257B Operating weight 6,668 lb (3024 kg) 7,559 lb (3428 kg) Rated operating capacity at 35 percent tipping load Rated operating capacity at 50 percent tipping load 1,367 lb (620 kg)1,950 lb (885 kg) 1,615 lb (732 kg)2,3100 lb (1047 kg) Engine model Cat 3024C T Cat 3024C T Net

Cat C18 Engine Specs & Advantages

The Cat® C18 Diesel Engine is offered in ratings ranging from 429-522 bkW (575-700 bhp) @ 1800-1900 rpm. Industries and applications powered by Cat C18 engines include: Agriculture, Ag Tractors, Bore/Drill Rigs, Chippers/Grinders, Compactors/Rollers, Compressors, Construction, Cranes, Forestry, General Industrial, Hydraulic Power Units, Irrigation Equipment, Material Handling, Mining, Mobile Earthmoving Equipment, Paving Equipment, Pumps, Shovels/Draglines, Surface Hauling Equipment and Trenchers. Cat C18 Specs With plenty of options to keep the engine package size to a minimum, the Cat C18 is a fully-configurable engine giving owners the power to customize based on a variety of applications. Cat C18 Engine Power Rating Maximum Power - 800 HP Maximum Torque - 2736 lb-ft @ 1300 rpm Rated Speed - 1800-2000 Minimum Power - 575 HP Emission Standards - EU Stage V Cat C18 Diesel Engine Specifications Engine Configuration - In-Line 6 Bore - 5.7 in Stroke - 7.2 in Displacement - 1

Caterpillar Equipment

Search This Blog